Showing 25–48 of 54 results
-
Viking – 4924A
13.6 m³/h
3.5 bar
107°C
--
Viking’s 4924A Series™ Positive Displacement (PD) pumps offer safety, reliability and high efficiency in refrigeration ammonia recirculation applications. Safety is achieved through use of a double mechanical dynamic shaft seal located between bearings for minimum possible shaft run-out, with a pressurized barrier fluid system, and O-ring type static seals where components are joined. Reliability is provided by slow speed operation and low differential pressures, which maximize bearing and seal life. And efficiency is inherent in the PD Internal Gear pumping principle, compared to centrifugal pumps. Viking pumps can usually use at least one motor size smaller than these technologies.
-
Viking – 4624B
- 41 m³/h
- 10 bar
- 150°C
- 55,000 cST
The 4624B Series™ internal gear pumps utilize hard parts in key wear areas, combined with unique designs and operating practices to reduce abrasive wear for longest life. These pumps are ideally suited for liquids with concentrations of small but hard particles, such as paints, inks and pigments; filled polyols and resins; and waste oils.
-
Viking – 1224A-CHC
- 90 m³/h
- 14 bar
- 107°C
- 200,000 cST
Customers, however, told us they wanted ONE pump to do it all. So we incorporated all of those features, and more, into our 1224A-CHC Series chocolate pumps to enable standardization of pumps and spares throughout the plant.
Whether the task is to transfer cocoa mass from a ball mill across the plant to a blending tank, or to recirculate yogurt coating in a closed loop to feed a series of panners, or to continuously recirculate tempered milk chocolate from an enrobing machine’s sump to the feed trough, or a hundred other possibilities, Viking’s gentle, reliable pumps will improve your operational efficiency
-
Viking – 4197-SEP
- 17 m³/h
- 14 bar
- 105°C
- 1,100 cST
The 4197-SEP Series™ pumps are specially fit with low temperature materials suitable for subzero solvent transfer or circulation applications. They are also assembled and tested using only food grade liquids.
-
Viking – SG
- 43 m³/h
- 34 bar
- 230°C
- 250,000 cST
Viking SG is an extensive series of precision, industrial-duty external gear pumps that develop higher pressures than other Viking pumps, yet offer a similarly broad range of options to handle a diverse range of liquids and applications
-
Viking – 4223A
- 114 m³/h
- 14 bar
- 427 °C
- 440,000 cST
Pumps are designed for a broad range of applications, from thin to thick, requiring continuous duty at pressures up to 200 PSI (14 Bar). Even higher pressures are possible with high fluid viscosities at reduced operating speeds (consult factory). They are also capable of operating under suction lift conditions and operate equally well in either direction.
The Universal Product Line has the broadest range of sealing options of all pumps built by Viking. The stuffing box on all sizes accepts packing, numerous component single mechanical seals, or a wide variety of cartridge seals.
The Universal Product Line is Viking Pump’s most versatile line of internal gear pumps due to the availability of many design and material options.
-
Viking – LVP
- 36 m³/h
- 14 bar
- 135°C
- 500 cST
The LVP Series™ is designed for thin, corrosive industrial liquids, flammable liquids which require corrosion protection and applications where pressures or vacuum requirements exceed other pumps’ capabilities. Vanes extend from slots on the rotor, sweeping liquid through a cam-shaped cavity. They offer the benefit of very low slip and high mechanical efficiency.
-
Viking – REVOLUTION
- 173 m³/h
- 31 bar
- 150°C
- 440,000 cST
TYPICAL APPLICATIONS: Pharmaceutical I Personal Care I Foods I Beverage I Dairy I Confectionary I Chemical
-
Viking – 893
- 17 m³/h
- 8.5 bar
- 260 °C
- 5,500 cST
893 Series pumps are designed to provide positive displacement pumping capability in those situations that require the highest assurance of liquid containment. These mag drive pumps provide for the safe, trouble-free transfer of hazardous, EPA-regulated fluids without electronic monitoring as required with mechanical face-type shaft seals. Hard-to-seal liquids are also easily handled with the Viking Mag Drive which eliminates the high cost of mechanical seal replacement and repair. A variety of coupling sizes are available for flow requirements to 75 GPM. The torquecarrying ability of high-strength magnets allows pumps to be coupled with gear reducers for slow-speed handling of viscous liquids. The self-priming positive-displacement
pumping principle provides low-shear, non-pulsing flow. Internal gear pumps are available in stainless steel, steel, and cast iron construction. -
Viking – 895
- 17 m³/h
- 8.5 bar
- 230 °C
- 5,500 cST
895 Series pumps are designed to provide positive displacement pumping capability in those situations that require the highest assurance of liquid containment. These mag drive pumps provide for the safe, trouble-free transfer of hazardous, EPA-regulated fluids without electronic monitoring as required with mechanical face-type shaft seals. Hard-to-seal liquids are also easily handled with the Viking Mag Drive which eliminates the high cost of mechanical seal replacement and repair. A variety of coupling sizes are available for flow requirements to 75 GPM. The torquecarrying ability of high-strength magnets allows pumps to be coupled with gear reducers for slow-speed handling of viscous liquids. The self-priming positive-displacement
pumping principle provides low-shear, non-pulsing flow. Internal gear pumps are available in stainless steel, steel, and cast iron construction. -
Viking – 897
- 17 m³/h
- 8.5 bar
- 260 °C
- 5,500 cST
897 Series pumps are designed to provide positive displacement pumping capability in those situations that require the highest assurance of liquid containment. These mag drive pumps provide for the safe, trouble-free transfer of hazardous, EPA-regulated fluids without electronic monitoring as required with mechanical face-type shaft seals. Hard-to-seal liquids are also easily handled with the Viking Mag Drive which eliminates the high cost of mechanical seal replacement and repair. A variety of coupling sizes are available for flow requirements to 75 GPM. The torquecarrying ability of high-strength magnets allows pumps to be coupled with gear reducers for slow-speed handling of viscous liquids. The self-priming positive-displacement
pumping principle provides low-shear, non-pulsing flow. Internal gear pumps are available in stainless steel, steel, and cast iron construction. -
Viking – 432
- 4.5 m³/h
- 17 bar
- 230 °C
- 55,000 cST
Viking’s Motor Speed Product Line internal gear pumps are extremely well suited for light, medium and intermittent service handling a variety of liquids. The smaller sizes C, F, FH are constructed for heavier duty service. Mechanical seal equipped pump models in sizes C, F, FH, G, H, HL are available with Underwriters label for handling fuel oil. Model numbers for these pumps must be designated by a suffix -X.
UL listed models can be equipped with integral relief valve. Viking’s unique and unusually simple pump construction makes it adaptable to many diversified installations. The pumps possess excellent vacuum characteristics and will operate and prime at suction lifts up to 25 feet, depending upon the vaporization point of volatile liquids. Because of the cushioned action in providing a continuous and steady stream of liquid without splashing, pounding, foaming or churning, the Viking pump is adaptable to an unlimited number of industrial applications
-
Viking – 456
- 0.7 m³/h
- 17 bar
- 177 °C
- 1,650 cST
The 456 Motor Mounted units answer the need for more compact, lighter weight equipment. They use the Series 456 hub type pumps with valves in casings and are mounted to modified NEMA “C” flange motors. Units are available with ¼, ⅓, ½ or ¾ HP, 1 ph, 1200 RPM or 1800 RPM, special shaft, TEFC or explosion proof motors. All sizes use the mounting flange bracket with pump connected to motor through a coupling. The pump can be turned on the bracket to any position desired.
-
Viking – 75
- 7 m³/h
- 7 bar
- 177 °C
- 550 cST
For compactness, less weight and simplicity of mounting, Viking’s line of close-coupled pumps are ideal for direct connecting to other pieces of equipment. The positive, smooth delivery of these pumps makes them preferred for many types of applications including filtering, circulating, transferring, lubricating or booster service.
-
Viking – 475
- 7 m³/h
- 7 bar
- 177 °C
- 550 cST
This advanced design is unique in its field for it permits use of STANDARD, unmodified NEMA C flange ball bearing motors.
-
Viking – 227A
- 73 m³/h
- 10 bar
- 175 °C
- 17,000 cST
Pumps are designed for a broad range of applications, from thin to thick, requiring continuous duty at pressures up to 200 PSI (14 Bar). Even higher pressures are possible with high fluid viscosities at reduced operating speeds (consult factory). They are also capable of operating under suction lift conditions and operate equally well in either direction.
The Universal Product Line has the broadest range of sealing options of all pumps built by Viking. The stuffing box on all sizes accepts packing, numerous component single mechanical seals, or a wide variety of cartridge seals.
The Universal Product Line is Viking Pump’s most versatile line of internal gear pumps due to the availability of many design and material options
-
Viking – TRA®10
- 102 m³/h
- 27 bar
- 150°C
- 200,000 cST
GEAR BOX: Powder-coated standard I 304 stainless steel optional
-
Viking – TRA®20
- 102 m³/h
- 34 bar
- 150°C
- 200,000 cST
GEAR BOX: Powder-coated standard I 304 stainless steel optional
-
Viking – 1227A
- 73 m³/h
- 10 bar
- 175 °C
- 17,000 cST
Viking Pump is the leader in internal gear innovation and the latest development is the O-Pro™ Seal technology. The NEW Universal Seal Product Line comes with the O-Pro Guard Seal factory installed. The Universal Product Line combines the tested reliability of the Universal pump & O-rings to create a robust seal and lubrication chamber, all in one.
-
Viking – STERILOBE
- 171 m³/h
- 15 bar
- 150°C
- 200,000 cST
Standard bi-wing rotors offer application flexibility & good solids handling capabilities
Multi-lobe rotors reduce shear & pulsation effect; ideal for sensitive media
Innovative cusps with reliefs allow for easier cleaning and self draining with improved efficiency -
Viking – CLASSIC+
- 189 m³/h
- 12 bar
- 180 °C
- 200,000 cST
Modular pump design promotes easy disassembly for COP (Clean Out of Place) & CIP (Clean In Place)
-
Viking – 4227A
- 73 m³/h
- 10 bar
- 260 °C
- 440,000 cST
Pumps are designed for a broad range of applications, from thin to thick, requiring continuous duty at pressures up to 200 PSI (14 Bar). Even higher pressures are possible with high fluid viscosities at reduced operating speeds (consult factory). They are also capable of operating under suction lift conditions and operate equally well in either direction.
The Universal Product Line has the broadest range of sealing options of all pumps built by Viking. The stuffing box on all sizes accepts packing, numerous component single mechanical seals, or a wide variety of cartridge seals.
The Universal Product Line is Viking Pump’s most versatile line of internal gear pumps due to the availability of many design and material options.
-
Viking – TR-IS
- 3,937 LPM
- 10.2 bar
- 150 °C
- 800 cP
316L stainless steel construction certified for 3A and in compliance with EHEDG standards
-
Viking – RTP
- 76.8 m³/h
- 12 bar
- 150 °C
- 200,000 cST
Designed specifically for the hygienic stainless steel road tanker industry, the RTP outperforms the competition by providing higher capacity, higher pressure and unmatched efficiency. The RTP can also reduce loading and unloading time by over 30%.
This increased performance, along with advanced durability, application flexibility, ease of installation and ease of maintenance provide a complete solution for your hygienic tanker needs.
