Hiển thị 1–9 của 50 kết quả
-
Flux – COMBIFLUX FP 314
Tối đa: 60 L / phút
Tối đa: 250 mPas
Bơm thùng phuy Combiflux FP 314 cho độ nhớt tối đa 250 mPas. Bơm COMBIFLUX không phớt model FP 314 phù hợp cho nhiều ứng dụng khác nhau, từ bơm đầy thùng rỗng nhỏ, thùng phuy 200 lít thậm chí lên đến 1.000 lít. Công nghệ làm mát thông minh của động cơ với vỏ hai lớp đảm bảo lưu thông không khí tối ưu và bảo vệ chống lại sự xâm nhập của hơi mạnh.
Thiết kế mô-đun cho phép máy bơm được vận hành với động cơ FEM 3070 (có sẵn cho nguồn điện 110 V hoặc 230V) hoặc động cơ pin không chổi than Li-ion FBM-B 3100. Động cơ giải phóng nhanh cho phép một số máy bơm chỉ hoạt động bằng một động cơ , giảm thiểu ô nhiễm chéo giữa các ống bơm và giảm chi phí.
-
Flux – JUNIORFLUX F 310
- 47 l/min
- 250 mPas
The small drum pump JUNIORFLUX F 310 with fixed motor FEM 3070 and mechanical seal is especially suitable for pumping comparatively small quantities out of containers such as canisters or drums of up to 200 litres. The small outer tube diameter allows pumping even out of narrow openings.
-
Flux – JUNIORFLUX F 314
- 57 l/min
- 250 mPas
The small sealless drum pump JUNIORFLUX F 314 with fixed motor FEM 3070 is especially suitable for pumping comparatively small quantities out of containers such as canisters or drums of up to 200 litres. The small outer tube diameter allows pumping even out of narrow openings.
-
Flux – F 430 PP-100/50
- 105 l/min
- 105 mPas
Pump F 430 PP 100/50 in polypropylene was designed for higher delivery pressure. Instead of a rotor, it is equipped with an impeller in a pump housing. In connection with the powerful FLUX motors the pump delivers a far higher pressure of over 3 bar compared to pumps with semi-axial rotors. This makes it especially convenient for conveying media out of e.g. IBCs and other containers into higher lying pipe systems or out of an IBC in the basement to a higher floor.
-
Flux – MINIFLUX
- 240 l/min
- 1000 mPas
The horizontally installed, compact container pump MINIFLUX is designed for emptying IBCs via their floor-level outlet. Designed as an alternative to a vertical pump, the MINIFLUX can be used when an IBC is not accessible from the top. It is suitable for applications when gravity draining via the outlet tap is insufficient e.g. rapid dispensing or transfer to another container in a higher location. Power can ideally be provided by a commutator or compressed air motor.
-
Flux – F 425 / FP 425
- 120 l/min
- 1200 mPas
With the Drum pump F/FP 425 there is less than 0.05 l residual amount left in a 200 l drum, so maximum 0.02 %. The pump has an integrated backflow valve that is easy to close before taking the pump out of the container. Thus the backflow of the medium in the pump is prevented. This makes optimum use of especially expensive media possible and saves additional cleaning and disposal costs when handling problematic media. The pump is available in stainless steel, polypropylene and hastelloy C. In stainless steel and hastelloy C the pump F/FP 425 can also be used in hazardous areas.
-
Flux – F 430 TR
- 240 l/min
- 1200 mPas
The horizontal Drum and container pump F 430 TR is ideal for conveying media from IBCs, tanks and other containers with low level outlet. E.g. if a tank is not accessible from the top, or if the spatial conditions do not allow use of a vertical pump. For cleaning, the pump can be easily and quickly taken apart in its two main components. The pump is available in stainless steel or polypropylene. The stainless steel version can also be used in hazardous areas.
-
Flux – F 427 / FP 427
- 240 l/min
- 1000 mPas
The Drum pump F/FP 427 is ideal for hygienic applications and suitable for conveying media out of drums, IBCs and other containers. It can be easily and quickly disassembled for cleaning / sterilization and can be completely stripped down to individual parts. The pump has minimal dead spots. The drive shaft, the inner and the outer tube are made of stainless steel (316 Ti resp. 1.4581). The pump is also available as FOOD and 3A certified version and complies with international safety standards.
-
Flux – F 426
- 240 l/min
- 1200 mPas
The Drum pump F 426 is ideal for mixing and/or pumping inhomogeneous media. You can keep media moving that tend to segregate, even during pumping. With the outlet closed, e.g. via a hand nozzle, the F 426 can be temporarily operated as pure mixing pump. By turning the adjusting lever, the pump can be easily adjusted to “mixing” or “pumping”. The pump is easy to dismantle for rapid cleaning. The pump is available in stainless steel and polypropylene. The stainless steel version can also be used in hazardous areas.
